直升机单机等距螺旋应召搜潜效能模型与仿真

等距螺旋法是直升机应召反潜中常用的搜潜样式。潜艇位置误差及航速误差对螺旋搜潜概率及搜潜战术运用具有显著影响。依据研究问题的逻辑关系,分别建立了潜艇速度散布模型和等距螺旋搜潜效能模型,运用蒙特卡罗法对直升机应召螺旋搜潜效能进行分析评估。实例验证了模型的可信度,提出了存在潜艇速度误差条件下,延迟时间和预估航速的改变对于搜潜效能的影响。     

双质量飞轮的弧形弹簧设计及仿真分析

为了研究双质量飞轮的减振特性及其在汽车上的使用情况，在分析弧形螺旋弹簧双质量飞轮工作原理的基础上，经过理论推导，得到了应用于双质量飞轮的弧形螺旋弹簧的刚度计算公式，根据此公式完成了2个弹簧和6个弹簧双质量飞轮的弹簧参数计算和结构设计；建立了车辆动力传动系统的多自由度扭振分析仿真模型，对2种形式双质量飞轮减振效果进行了仿真分析。分析结果对设计适用于已知工况的双质量飞轮具有实用意义。     

离子束加工误差对散射损失的影响研究

离子束加工(Ion Beam Figuring,IBF)去除函数对加工残差具有重要的影响,而加工残差引起的表面散射则导致光学性能发生变化.为了减小加工残差对光学性能的影响,利用基于CCOS成形原理的离子束加工仿真程序对光学镜面进行修形,分析不同去除函数宽度对散射损失(Ratio of Scattering Loss,RSL)指标的影响.通过研究可知,随着去除函数宽度的减小,加工残差对散射损失的影响越来越小.因此,根据加工残差对RSL指标的影响程度以及RSL指标要求,可以合理选择去除函数宽度,从而在满足面形精度的同时,优化加工工艺.     

Dynamic signatures and their use in comparing the reliability of new and used systems

The signature of a system with independent and identically distributed (i.i.d.) component lifetimes is a vector whose ith element is the probability that the ith component failure is fatal to the system. System signatures have been found to be quite useful tools in the study and comparison of engineered systems. In this article, the theory of system signatures is extended to versions of signatures applicable in dynamic reliability settings. It is shown that, when a working used system is inspected at time t and it is noted that precisely k failures have occurred, the vector s [0,1]^n‐k whose jth element is the probability that the (k + j)th component failure is fatal to the system, for j = 1,2,2026;,n ‐ k, is a distribution‐free measure of the design of the residual system. Next, known representation and preservation theorems for system signatures are generalized to dynamic versions. Two additional applications of dynamic signatures are studied in detail. The well‐known “new better than used” (NBU) property of aging systems is extended to a uniform (UNBU) version, which compares systems when new and when used, conditional on the known number of failures. Sufficient conditions are given for a system to have the UNBU property. The application of dynamic signatures to the engineering practice of “burn‐in” is also treated. Specifically, we consider the comparison of new systems with working used systems burned‐in to a given ordered component failure time. In a reliability economics framework, we illustrate how one might compare a new system to one successfully burned‐in to the kth component failure, and we identify circumstances in which burn‐in is inferior (or is superior) to the fielding of a new system. © 2009 Wiley Periodicals, Inc. Naval Research Logistics, 2009     

Effect of tool rotational speed on the particle distribution in friction stir welding of AA6092/17.5 SiCp-T6 composite plates and its consequences on the mechanical property of the joint

This study investigates the effect of tool rotational speed (TRS) on particle distribution in nugget zone (NZ) through quantitative approach and its consequences on the mechanical property of friction stir welded joints of AA6092/17.5 SiC_p-T6 composite. 6 mm thick plates are welded at a constant tool tilt angle of 2° and tool traverse speed of 1 mm/s by varying the TRS at 1000 rpm, 1500 rpm and 2000 rpm with a taper pin profiled tool. Microstructure analysis shows large quantity of uniformly shaped smaller size SiC particle with lower average particle area which are homogeneously distributed in the NZ. The fragmentation of bigger size particles has been observed because of abrading action of the hard tool and resulting shearing effect and severe stress generation due to the rotation of tool. The particles occupy maximum area in the matrix compared to that of the base material (BM) due to the redistribution of broken particles as an effect of TRS. The migration of particles towards the TMAZ-NZ transition zone has been also encountered at higher TRS (2000 rpm). The microhardness analysis depicts variation in average hardness from top to bottom of the NZ, minimum for 1500 rpm and maximum for 2000 rpm. The impact strength at 1000 rpm and 1500 rpm remains close to that of BM (21.6 J) while 2000 rpm shows the accountable reduction. The maximum joint efficiency has been achieved at 1500 rpm (84%) and minimum at 1000 rpm (68%) under tensile loading. Fractographic analysis shows mixed mode of failure for BM, 1000 rpm and 1500 rpm, whereas 2000 rpm shows the brittle mode of failure.     

型号研制与产品数据管理

介绍了产品数据管理(PDM)的概念和基本功能,结合当前型号研制的特点和计算机信息技术应用的状况、发展,研究了型号研制产品数据管理的需求、功能及实施,为当前型号研制依靠CIMS技术实现产品数据管理提出了8条基本原则。     

Does Military Spending Nonlinearly Affect Economic Growth in South Africa?

Using annual data collected from 1988 to 2015, this study provides evidence of a non-linear relationship between military spending, economic growth and other growth determinants for the South African economy. The empirical study is based on estimates of a logistic smooth transition regression (LSTR) model and our empirical results point to an inverted U-shaped relationship between military spending and economic growth for the data. Furthermore, our empirical results suggest that the current levels of military spending, as a component of total government expenditure, are too high in the South African economy and need to be transferred towards more productive non-military expenditure in order to improve the performance of economic growth and other growth determinants.     

无源RFID系统中推断式二进制搜索算法

在现有的RFID标准中，一般标签ID都由几个不同含义区间组成。针对这种特点，提出推断式二进制防碰撞算法：在识别每个区间段的ID时，利用某个特定读写器中的前缀库推断该区间段各个位的取值，以便减少待识别标签ID的位数。同时，通过调整参数u，可以对系统可靠性进行控制。仿真实验表明，在没有新前缀出现的情况下，推断式二进制防碰撞算法能够将QT算法的识别速度提高3倍、标签平均响应次数降低3／4。     

高超声速滑翔再入飞行器的可达区快速预测

防御方对来袭滑翔再入飞行器进行可达区的预测存在先验信息量不足且时效性要求高等难题.为此提出一种基于最优化飞行假设的可达区快速预测方法:仅需已知目标当前位置、速度与最大升阻比(可基于雷达探测数据通过实时弹道估计获得),基于平衡滑翔假设和最大横程的埃格斯解分别获得目标最大纵程和横程终点坐标,在经纬度二维平面内,可达区即可近...